KPV vs BPC-157: what the lab reports show

A three-residue peptide and a fifteen-residue one that are often listed next to each other. This page compares them strictly as analytical objects: sequence, formula, theoretical mass, and what a certificate of analysis for each has to show before it can be read as identifying the material it names.

Research-use scope. This page describes laboratory research materials and their analytical documentation. It is not for use in people or animals, contains no handling, preparation, or procedural guidance, and makes no claim that any material named here is safe or effective for any purpose. It compares identity and documentation only; it does not compare, rank, or recommend the materials for any application.

A tripeptide and a pentadecapeptide

KPV is the tripeptide lysine-proline-valine, the three C-terminal residues of alpha-melanocyte-stimulating hormone. BPC-157 is a synthetic chain of fifteen residues whose sequence comes from a larger protein first described in gastric juice; it is covered residue by residue in BPC-157: peptide identity, purity, and stability. The figures below are the ones published on the KPV 10mg and BPC-157 10mg listings, with the expected ions calculated from those formulas.

PropertyKPVBPC-157
SequenceLys-Pro-Val (KPV)GEPPPGKPADDAGLV
Residue count315
TerminiFree amine, free acidFree amine, free acid
Molecular formulaC16H30N4O4C62H98N16O22
CAS registry number67727-97-3137525-51-0
Theoretical average mass342.4 g/mol1,419.5 g/mol
Theoretical monoisotopic massapproximately 342.2approximately 1,418.7
Expected singly charged ion [M+H]+near m/z 343.2near m/z 1,419.7
Expected doubly charged ion [M+2H]2+near m/z 172.1near m/z 710.4
Sulfur in the formulaNoneNone
Aromatic residuesNoneNone
Physical form suppliedLyophilized solidLyophilized solid

An N-acetylated, C-amidated form of KPV also appears in the literature. It has the formula C18H33N5O4 and sits about 41 units heavier, near 383.5 g/mol, so the stated formula and mass also tell you which form a report describes. The masses above are calculated from the formulas on the listings; the report for a specific lot is the authoritative record.

Why a very short peptide is harder to read than it looks

What each certificate of analysis must show

Report sectionFor a KPV lotFor a BPC-157 lot
IdentityObserved mass in agreement with 342.4 g/mol (monoisotopic near 342.2), with the ion and its charge stated, or HPLC-RTM against a named KPV reference standard; the formula should say whether the free or the capped form is meantObserved mass in agreement with 1,419.5 g/mol (monoisotopic near 1,418.7) within tolerance, or HPLC-RTM against a named BPC-157 reference standard
Chromatographic purityMain-peak area as a percentage of total integrated area, with the chromatogram published; the main peak should sit clear of the solvent frontThe same figure and trace; near-eluting deletion peaks are the expected signature
Net contentMeasured mg of peptide in the vial, stated next to the labeled strengthMeasured mg of peptide in the vial, stated next to the labeled strength
EndotoxinWhere tested: the method (LAL, with the USP <85> reference if claimed), the result with its units (EU per mL, per mg or per vial), and the limit it was compared against.
Heavy metalsWhere tested: the elements in the panel, the method, and a result or "none detected" against a stated reporting limit.
Method fieldsColumn, mobile phase or gradient, detection wavelength, and reporting limit. A percentage with no method attached is not a result.
Record fieldsMaterial name, labeled strength, lot identifier matching the vial label, test date, certificate or accession number, and the issuing laboratory with its verification route.

Endotoxin and heavy-metal screens are only part of a report when the laboratory ran them. If a line is not on the certificate, that test was not performed on that lot; it has not been passed. The endotoxin testing guide explains what a LAL result and a USP <85> pass mean, and net peptide content explains why the measured mg can differ from the label.

How to tell them apart on paper

  1. Find the stated mass. Near 342 is KPV (near 383 if capped at both ends); near 1,419 is BPC-157. There is no overlap.
  2. Count the residues if a sequence is printed. Three against fifteen.
  3. Read the ion list. A KPV report shows ions near m/z 343 and 172; a BPC-157 report shows ions near 1,419.7 and 710.4.
  4. Check that the identity line names its reference. A retention-time result is only meaningful against a named standard for the same compound.

How to read our reports for these two

Our current reports come from three laboratories. Freedom Diagnostics reports give purity by HPLC-UV, identity by LC-MS, net content in mg, and an endotoxin result where one is listed; each carries an accession number and a search code for the laboratory's lookup page. ILS Laboratories reports give purity by HPLC, identity by retention-time match against a reference standard, net peptide content, and the screens run on that lot. Janoshik Analytical reports carry the laboratory's own verification key. Verify a lab report walks through each lookup.

On Arctic Lab Supply reports. Every currently published report is listed in the batch COA library with its certificate or accession number and verification link. The report for the lot you receive is the one that governs; where an earlier lot's figures differ, the lot-specific report is authoritative.

Common questions

How do KPV and BPC-157 differ on a certificate of analysis?

KPV is the tripeptide Lys-Pro-Val, C16H30N4O4, 342.4 g/mol. BPC-157 is a 15-residue peptide, C62H98N16O22, 1,419.5 g/mol. The stated mass, the residue count and the ions in the mass-spectrometry section are all different, so a report for one cannot describe the other.

What mass should each report state?

KPV: about 342.2 (monoisotopic) or 342.4 g/mol (average), seen near m/z 343.2 as [M+H]+. BPC-157: about 1,418.7 (monoisotopic) or 1,419.5 g/mol (average), near m/z 1,419.7 and 710.4. A capped (N-acetyl, C-amide) KPV would sit near 383.5 g/mol.

Why does a high purity figure say less for KPV than for a longer peptide?

A three-residue chain has only two coupling steps, so few synthesis impurities are possible and high figures are typical. The more useful checks are that the main peak is well separated from the solvent front, that the detection wavelength is stated, and that net content is reported.

Which KPV and BPC-157 lots are documented on this site?

BPC-157 10mg lot BP-2501A (Freedom Diagnostics, 99.27%, Oct 15, 2026) and BPC-157 5mg lot BCP-2502-B (ILS Laboratories, 99.59%, Aug 25, 2026) have published reports. KPV 10mg was listed in November 2026; its lot report is posted on the product page and in the COA library when it is back.

Related documentation